Product Details:
Minimum Switching Current | Configurable relay logic 3 mA at 24 V DC |
Transmission Frame | RTU for Modbus |
Analogue Output Number | 1 |
Discrete Input Number | 7 |
Discrete Output Number | 2 |
Frequency Resolution | Analog input 0.024/50 Hz, Display unit 0.1 Hz |
Marking | CE |
Operating Position | Vertical +/- 10 degree |
Physical Interface | 2-wire RS 485 for Modbus |
Model No | ATV71H037M3 |
Motor Power HP | 0.5 hp at 200 to 240 V 3 phase |
Number of Addresses | 1 to 247 for Modbus, 1 to 127 for CANopen |
Method of Access | Slave for CANopen |
Shock Resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Ambient Air Temperature for Operation | -10 to 50 Deg C without derating |
Operating Altitude | Less Than or Equal 1000 m without derating, 1000 to 3000 m with current derating 1 % per 100 m |
Product Weight | 3 Kg |
Linearity Error | AI1-/Al1+, AI2 +/- 0.15 % of maximum value, AO1 +/- 0.2 % |
Width | 130 mm |
Depth | 175 mm |
Height | 230 mm |
Network Number of Phase | 3 phase |
Line Current | 3.1 A for 240 V 3 phases 0.37 kW / 0.5 hp, 3.5 A for 200 V 3 phases 0.37 kW / 0.5 hp |
Apparent Power | 1.3 kVA at 240 V 3 phases 0.37 kW / 0.5 hp |
Nominal Output Current | 3 A at 4 kHz 230 V 3 phases 0.37 kW / 0.5 hp |
Synchronous Motor Control Profile | Vector control without speed feedback |
Local Signalling | 1 LED red presence of drive voltage |
Insulation | Electrical between power and control |
Insulation Resistance | Greater Than 1 mOhm at 500 V DC for 1 minute to earth |
Communication Port Protocol | CANopen Modbus |
Motor cable length | <= 50 m Shielded cable <= 100 m Unshielded cable |
Asynchronous motor control profile | ENA (Energy adaptation) system for unbalanced loads Flux vector control (FVC) with sensor (current vector) Sensorless flux vector control (SFVC) (voltage or current vector) Voltage/Frequency ratio (2 or 5 points) |
Product destination | Asynchronous motors Synchronous motors |
Speed range | 1 to 100 for asynchronous motor in open-loop mode, without speed feedback 1 to 50 for synchronous motor in open-loop mode, without speed feedback 1 to 1000 for asynchronous motor in closed-loop mode with encoder feedback |
Speed accuracy | +/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation in closed-loop mode with encoder feedback +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback |
Transient Overtorque | 220 % of nominal motor torque +/- 10 % for 2 s 170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes |
Motor slip compensation | Adjustable Automatic whatever the load Not available in voltage/frequency ratio (2 or 5 points) Suppressable |
Type of cable | With a NEMA Type1 kit : 3-strand UL 508 cable at 40 ??C, copper 75 ??C PVC With an IP21 or an IP31 kit : 3-strand IEC cable at 40 ??C, copper 70 ??C PVC Without mounting kit : 1-strand IEC cable at 45 ??C, copper 70 ??C PVC Without mounting kit : 1-strand IEC cable at 45 ??C, copper 90 ??C XLPE/EPR |
Electrical connection | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm?? / AWG 14 L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 4 mm?? / AWG 10 |
Tightening torque | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 1.4 N.m / 12.3 lb.in |
Supply | Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %, <= 10 mA for overload and short-circuit protection Internal supply, 24 V DC, voltage limits 21...27 V, <= 200 mA for overload and short-circuit protection |
Analogue input type | AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + sign AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bits AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits |
Sampling duration | AI1-/Al1+ 2 ms, +/- 0.5 ms for analog input(s) Al2 2 ms, +/- 0.5 ms for analog input(s) LI1...LI5 2 ms, +/- 0.5 ms for discrete input(s) LI6 (if configured as logic input) 2 ms, +/- 0.5 ms for discrete input(s) |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Number |
Acceleration And Deceleration Ramps | S, U, Linear from 0 to 999.9 s |
Assembly Style | With Heat Sink |
Continuous Output Current | 2.4 A 4 kHz |
Phase | 1 Phase |
Maximum Transient Current | 3.6 A 60 s |
Minimum Switching Current | 5 mA 24 V DC logic relay |
Product Or Component Type | Variable Speed Drive |
Connector Type | 1 RJ45 Modbus on front face |
Quantity Per Set | Set of 1 |
Transmission Frame | RTU Modbus |
Braking Torque | Up to 70 % of nominal motor torque without braking resistor |
Speed Range | 1 to 20 |
Ambient Air Temperature For Storage | -13 to 158 Deg F (-25 to 70 Deg C) |
Analogue Input Number | 1 |
Analogue Output Number | 1 |
Braking To Standstill | By DC injection Less Than or Equal 30 s |
Component Name | ATV12 |
Discrete Input Number | 4 |
Discrete Output Number | 2 |
Emc Filter | Integrated |
Frequency Resolution | 0.1 Hz display unit, Converter A/D, 10 bits analog input |
Functionality | Basic |
Marking | CE |
Noise Level | 0 dB |
Nominal Switching Frequency | 4 kHz |
Number Of Addresses | 1 to 247 Modbus |
Operating Position | Vertical +/- 10 degree |
Output Voltage | 200 to 240 V 3 phase |
Physical Interface | 2-wire RS 485 Modbus |
Product Destination | Asynchronous Motors |
Product Specific Application | Simple Machine |
Prospective Line Isc | Less Than or Equal 1 kA |
Range Of Product | Altivar 12 |
Specific Application | Commercial Equipment |
Speed Drive Output Frequency | 0.5 to 400 Hz |
Switching Frequency | 2 to 16 kHz adjustable, 4 to 16 kHz with derating factor |
Tightening Torque | 7.08 lbf.in (0.8 N.m) |
Transmission Rate | 4800 bit/s, 9600 bit/s, 19200 bit/s, 38400 bit/s |
Model No | ATV12H037M2 |
Discrete Input Type | Programmable LI1 to LI4 24 V 18 to 30 V |
Sampling Duration | 20 ms +/- 1 ms logic input, 10 ms analogue input |
Linearity Error | +/- 0.3 % of maximum value analogue input |
Discrete Output Type | Logic output LO+, LO /Protected relay output R1A, R1B, R1C 1 C/O |
Time Constant | 20 ms +/- 1 ms for reference change |
Depth | 4.77 in (121.2 mm) |
Product Weight | 1.54 lb(US) (0.7 kg) |
Motor Sstarter Type | Variable speed drive |
Shock Resistance | 15 gn EN/IEC 60068-2-27 11 ms |
Relative Humidity | 5 to 95 % without condensation IEC 60068-2-3 5 to 95 % without dripping water IEC 60068-2-3 |
Transient Overtorque | 150 to 170 % of nominal motor torque depending on drive rating and type of motor |
Rated Supply Voltage | 200 to 240 V - 15 to 10 % |
Motor Power kW | 0.37 |
Motor Power HP | 0.55 |
Communication Port Protocol | Modbus |
Line Current | 5.9 A 200 V, 4.9 A 240 V |
Asynchronous Motor Control Profile | Voltage/Frequency ratio (V/f), Quadratic voltage/frequency ratio, Sensorless flux vector control |
IP Degree of Protection | IP20 without blanking plate on upper part |
Supply Frequency | 50/60 Hz +/- 5 % |
Motor Slip Compensation | Preset in factory Adjustable |
Built in Fan | Without |
Electrical Connection | Terminal 3.5 mm2 AWG 12 L1, L2, L3, U, V, W, PA, PC |
Insulation | Electrical between power and control |
Communication service | Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/Write multiple registers (23) 4/4 words Read device identification (43) |
Supply | Internal supply for reference potentiometer 5 V DC 4.75 to 5.25 V 10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4 to 28.8 V 100 mA overload and short-circuit protection |
Analogue input type | Configurable voltage AI1 0 to 10 V 30 kOhm Configurable voltage AI1 0 to 5 V 30 kOhm Configurable current AI1 0 to 20 mA 250 Ohm |
Discrete Input Logic | Negative logic (sink) > 16 V < 10 V 3.5 kOhm Positive logic (source) 0 to < 5 V > 11 V |
Analogue output type | Software-configurable voltage AO1 0 to 10 V 470 Ohm 8 bits Software-configurable current AO1 0 to 20 mA 800 Ohm 8 bits |
Maximum Switching current | 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay |
Protection type | Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases |
Discrete and process manufacturing | Commercial equipment : mixer Commercial equipment : other application Textile : ironing |
Electromagnetic compatibility | Immunity to conducted disturbances level 3 EN/IEC 61000-4-6 Surge immunity test level 3 EN/IEC 61000-4-5 Voltage dips and interruptions immunity test EN/IEC 61000-4-11 Electrical fast transient/burst immunity test level 4 EN/IEC 61000-4-4 Electrostatic discharge immunity test level 3 EN/IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 EN/IEC 61000-4-3 |
Electromagnetic emission | Radiated emissions environment 1 category C2 EN/IEC 61800-3 2...16 kHz shielded motor cable Conducted emissions with integrated EMC filter environment 1 category C1 EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable 5 m Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2...12 kHz shielded motor cable 5 m Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable 10 m Conducted emissions with additional EMC filter environment 1 category C1 EN/IEC 61800-3 4...12 kHz shielded motor cable 20 m Conducted emissions with additional EMC filter environment 1 category C2 EN/IEC 61800-3 4...12 kHz shielded motor cable 50 m Conducted emmissions with additional EMC filter environment 2 category C3 EN/IEC 61800-3 4 to 12 Khz Shielded motor cable 50 m |
Additional Information:
Product Details:
Assembly Style | With Heat Sink |
Continuous Output Current | 144 A at 12 kHz, 230 V 3 phase |
Maximum Transient Current | 172.8 A for 60 s 3 Phase |
Minimum Switching Current | Configurable relay logic 3 mA at 24 V DC |
Product Or Component Type | Variable Speed Drive |
Regulation Loop | Frequency PI regulator |
Transmission Frame | RTU for Modbus |
Braking Torque | 30 % without braking resistor / Less Than or Equal 125 % with braking resistor |
Speed Accuracy | +/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback |
Speed Range | 1 to 100 in open-loop mode, without speed feedback |
Analogue Input Number | 2 |
Analogue Output Number | 1 |
Component Name | ATV61 |
Discrete Input Number | 7 |
Discrete Output Number | 2 |
Emc Filter | Without EMC Filter |
Frequency Resolution | Analog input 0.024/50 Hz / Display unit 0.1 Hz |
Marking | CE |
Network Frequency | 47.5 to 63 Hz |
Noise Level | 64 dB conforming to 86/188/EEC |
Nominal Switching Frequency | 12 kHz |
Operating Position | Vertical +/- 10 degree |
Output Frequency | 0.1 to 599 Hz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Physical Interface | 2-wire RS 485 for Modbus |
Product Destination | Asynchronous motors / Synchronous motors |
Product Specific Application | Pumping and Ventilation Machine |
Prospective Line Isc | 22 kA 3 phases |
Range Of Product | Altivar 61 |
Supply Voltage Limits | 170 to 264 V |
Switching Frequency | 1 to 16 kHz adjustable / 12 to 16 kHz with derating factor |
Torque Accuracy | +/- 15 % in open-loop mode, without speed feedback |
Type Of Polarization | No impedance for Modbus |
Model No | ATV61HD37M3X |
Width | 320 mm |
Height | 550 mm |
Depth | 266 mm |
Motor Power HP | 50 hp 3 phases at 200 to 240 V |
Shock Resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Ambient Air Temperature for Operation | -10 to 50 Deg C without derating / 50 to 60 Deg C with derating factor |
Ambient Air Ttemperature for Sstorage | -25 to 70 Deg C |
Rated Supply Voltage | 200 to 240 V (- 15 to 10 %) |
Network Nnumber of Phase | 3 Phase |
Apparent Power | 52.8 kVA for 240 V 3 phases 37 kW / 50 hp |
Local Signalling | 1 LED red presence of drive voltage |
Synchronous Motor Control Profile | Vector control without sensor, standard |
Supply Frequency | 50 to 60 Hz (- 5 to 5 %) |
Transient Overtorque | 130 % of nominal motor torque, +/- 10 % for 60 s |
Isolation | Between power and control terminals |
Braking to Standstill | By DC injection |
Insulation Resistance | Greater Than 1 mOhm at 500 V DC for 1 minute to earth |
Motor Power kW | 37 kW 3 phases at 200 to 240 V |
Number of Addresses | 1 to 247 for Modbus / 1 to 127 for CANopen |
Method of Access | Slave for CANopen |
Product Weight | 37 Kg |
Asynchronous motor control profile | Voltage/Frequency ratio, 2 points Voltage/Frequency ratio, 5 points Flux vector control without sensor, standard Voltage/Frequency ratio - Energy Saving, quadratic U/f |
Option card | APOGEE FLN communication card BACnet communication card CC-Link communication card Controller inside programmable card DeviceNet communication card Ethernet/IP communication card Fipio communication card I/O extension card Interbus-S communication card LonWorks communication card METASYS N2 communication card Modbus Plus communication card Modbus TCP communication card Modbus/Uni-Telway communication card Multi-pump card Profibus DP communication card Profibus DP V1 communication card |
Motor slip compensation | Adjustable Automatic whatever the load Can be suppressed Not available in voltage/frequency ratio (2 or 5 points) |
Type of cable | With an IP21 or an IP31 kit : 3-strand IEC cable at 40 °C, copper 70 °C PVC Without mounting kit : 1-strand IEC cable at 45 °C, copper 70 °C PVC Without mounting kit : 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR With UL Type 1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVC |
Electrical connection | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 to LI6, PWR terminal 2.5 mm² / AWG 14 L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 150 mm² / 300 kcmil |
Tightening torque | L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 41 N.m / 360 lb.in AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 to LI6, PWR 0.6 N.m |
Supply | Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10 mA for overload and short-circuit protection Internal supply 24 V DC (21 to 27 V), <= 200 mA for overload and short-circuit protection External supply 24 V DC (19 to 30 V) |
Analogue input type | AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + sign AI2 software-configurable current 0 to 20 mA, impedance 242 Ohm, resolution 11 bits AI2 software-configurable voltage 0 to 10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits |
Sampling duration | Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 ms Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms Analog input Al2 2 ms, +/- 0.5 ms Analog output AO1 2 ms, +/- 0.5 ms Discrete input LI1...LI5 2 ms, +/- 0.5 ms |
Accuracy | AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C AI2 +/- 0.6 % for a temperature variation 60 °C AO1 +/- 1 % for a temperature variation 60 °C |
Linearity error | AI1-/Al1+ +/- 0.15 % of maximum value AI2 +/- 0.15 % of maximum value AO1 +/- 0.2 % |
Additional Information:
Product Details:
Assembly Style | With Heat Sink |
Continuous Output Current | 7.1 A at 4 kHz |
Maximum Transient Current | 10.7 A for 60 s |
Minimum Switching Current | R1-R2 10 mA at 5 V DC |
Product Or Component Type | Variable Speed Drive |
Connector Type | 1 RJ45 Modbus/CANopen |
Transmission Frame | RTU |
Regulation Loop | Frequency PI Regulator |
Speed Range | 1 to 50 |
Analogue Input Number | 3 |
Analogue Output Number | 1 |
Component Name | ATV312 |
Discrete Input Number | 6 |
Discrete Output Number | 2 |
Emc Filter | Integrated |
Frequency Resolution | Analog input 0.1 to 100 Hz / Display unit 0.1 Hz |
Marking | CE |
Network Frequency | 47.5 to 63 Hz |
Nominal Switching Frequency | 4 kHz |
Operating Position | Vertical +/- 10 degree |
Output Frequency | 0 to 500 kHz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Physical Interface | RS485 multidrop serial link |
Pollution Degree | 2 |
Product Destination | Asynchronous Motors |
Product Specific Application | Simple Machine |
Prospective Line Isc | 5 kA |
Range Of Product | Altivar 312 |
Response Time | AOV, AOC 8 ms for analog / R1A, R1B, R1C, R2A, R2B 8 ms for discrete |
Supply Voltage Limits | 323 to 550 V |
Switching Frequency | 2 to 16 kHz adjustable |
Model No | ATV312HU30N4 |
Apparent Power | 7.1 kVA |
Power Dissipation | 125 W at Nominal Load |
Linearity Error | +/- 0.2 % for output |
Communication Port Protocol | CANopen Modbus |
Transient Overtorque | 170 to 200 % of nominal motor torque |
Insulation | Electrical between power and control |
Sampling Duration | AI1, AI2, AI3 8 ms for analog / LI1 to LI6 4 ms for discrete |
Discrete Input Type | (LI1 to LI6) programmable, 24 V 0 to 100 mA with PLC, impedance 3500 Ohm |
Braking to Standstil | By DC injection |
Time Constant | 5 ms for reference change |
Network Number of Phase | 3 Phase |
Number of Addresses | 1 to 247 Modbus / 1 to 127 CANopen |
Number of Drive | 127 CANopen / 31 Modbus |
Outer Dimension | 184 x 140 x 150, 215 x 185 x 158, 402 x 239 x 192 mm |
Height | 184 mm |
Width | 142 mm |
Depth | 152 mm |
Product Weight | 3.1 kg |
Protective Treatment | TC |
Shock Resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Ambient Air Temperature for Storage | -25 to 70 Deg C |
Line Current | 10.9 A for 380 V, 5 kA / 8.3 A for 500 V |
Asynchronous motor control profile | Factory set : constant torque Sensorless flux vector control with PWM type motor control signal |
Electrical connection | L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 5 mm?? AWG 10 Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm?? AWG 14 |
Supply | Internal supply for logic inputs at 19...30 V, <= 100 mA for overload and short-circuit protection Internal supply for reference potentiometer (2.2 to 10 kOhm) at 10...10.8 V, <= 10 mA for overload and short-circuit protection |
IP degree of protection | IP20 on upper part without cover plate IP21 on connection terminals IP31 on upper part IP41 on upper part |
Option card | CANopen daisy chain communication card DeviceNet communication card Fipio communication card Modbus TCP communication card Profibus DP communication card |
Braking torque | 100 % with braking resistor continuously 150 % without braking resistor 150 % with braking resistor for 60 s |
Motor slip compensation | Adjustable Automatic whatever the load Suppressable |
Tightening torque | 1.2 N.m L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 0.6 N.m Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1 to LI6 |
Analogue input type | AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance 30000 Ohm AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm AI3 configurable current 0...20 mA, impedance 250 Ohm |
Sampling duration | AI1, AI2, AI3 8 ms for analog LI1...LI6 4 ms for discrete |
Analogue output type | AOC configurable current 0...20 mA, impedance 800 Ohm, resolution 8 bits AOV configurable voltage 0...10 V, impedance 470 Ohm, resolution 8 bits |
Discrete input logic | (LI1...LI4) logic input not wired, < 13 V (state 1) (LI1...LI6) negative logic (source), > 19 V (state 0) (LI1...LI6) positive logic (source), < 5 V (state 0), > 11 V (state 1) |
Discrete output type | (R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles (R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles |
Maximum switching current | R1-R2 on inductive load, 2 A at 250 V AC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on inductive load, 2 A at 30 V DC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on resistive load, 5 A at 250 V AC, (cos phi = 1, and L/R = 0 ms) R1-R2 on resistive load, 5 A at 30 V DC, (cos phi = 1, and L/R = 0 ms) |
Acceleration and deceleration ramps | Linear adjustable separately from 0.1 to 999.9 s S, U or customized |
Additional Information:
Product Details:
Acceleration And Deceleration Ramps | Automatic based on the load, Linear adjustable separately from 0.01 to 3200 s |
Assembly Style | With Heat Sink |
Continuous Output Current | 88 A 230 V |
Ip Degree Of Protection | IP21 |
Maximum Transient Current | 96.8 A 60 s |
Minimum Switching Current | 3 mA 24 V DC configurable relay logic |
Product Or Component Type | Variable Speed Drive |
Connector Type | 1 RJ45, 1 open style |
Transmission Frame | RTU |
Regulation Loop | Adjustable PI Regulator |
Speed Accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn |
Speed Range | 1 to 10 |
Air Flow | 261 m3/h |
Ambient Air Temperature For Storage | -25 to 70 Deg C |
Analogue Input Number | 2 |
Analogue Output Number | 1 |
Braking To Standstill | By DC injection |
Data Format | 8 bits, 1 stop, odd even or no configurable parity |
Device Short Name | ATV212 |
Discrete Output Number | 2 |
Emc Filter | Without EMC Filter |
Frequency Resolution | 0.024/50 Hz analog input, 0.1 Hz display unit |
Marking | CE |
Motor Starter Type | Variable Speed Drive |
Network Frequency | 47.5 to 63 Hz |
Noise Level | 59.9 dB 86/188/EEC |
Nominal Switching Frequency | 8 kHz |
Number Of Addresses | 1 to 247 |
Operating Position | Vertical +/- 10 degree |
Option Card | Communication card LonWorks |
Output Voltage | Less Than or Equal Power Supply Voltage |
Physical Interface | 2-wire RS 485 |
Pollution Degree | 3 IEC 61800-5-1 |
Product Destination | Asynchronous Motors |
Product Specific Application | Pumps and fans in HVAC |
Prospective Line Isc | 22 kA |
Range Of Product | Altivar 212 |
Specific Application | HVAC |
Speed Drive Output Frequency | 0.5 to 200 Hz |
Supply Voltage Limits | 170 to 264 V |
Switching Frequency | 6 to 16 kHz adjustable, 8 to 16 kHz with derating factor |
Torque Accuracy | +/- 15 % |
Transmission Rate | 9600 bps or 19200 bps |
Type Of Polarization | No impedance |
Model No | ATV212HD22M3X |
Motor Slip Compensation | Adjustable, Automatic whatever the load, Not available in voltage/frequency ratio motor control |
Local Signalling | 1 LED red DC bus energized |
Isolation | Electrical Between Power and Control |
Dielectric Strength | 2830 V DC between earth and power terminals, 4230 V DC between control and power terminals |
Insulation Resistance | Greater Than or Equal 1 MOhm 500 V DC for 1 minute |
Communication Port Protocol | Apogee Fln, BACnet, LonWorks, METASYS N2, Modbus |
Depth | 214 mm |
Product Weight | 27.4 Kg |
Power Dissipation | 763 W |
Discrete and Process Manufacturing | Building - HVAC compressor for scroll, Building - HVAC fan, Building - HVAC pump |
Network Number of Phases | 3 Phases |
Power Range | 15 to 25 kW at 200 to 240 V 3 phases |
Vibration Resistance | 1 gn 13 to 200 Hz EN/IEC 60068-2-8, 1.5 mm 3 to 13 Hz EN/IEC 60068-2-6 |
Shock Resistance | 15 gn 11 ms IEC 60068-2-27 |
Environmental Characteristic | Classes 3C1 IEC 60721-3-3, Classes 3S2 IEC 60721-3-3 |
Relative Humidity | 5 to 95 % without condensation IEC 60068-2-3, 5 to 95 % without dripping water IEC 60068-2-3 |
Ambient Air Temperature for Operation | -10 to 40 Deg C without derating, Greater Than 40 to 50 Deg C with derating factor |
Motor Power | 22 kW |
Motor Power HP | 30 |
Rated Supply Voltage | 200 to 240 V - 15 to 10 % |
Supply Frequency | 50 to 60 Hz - 5 to 5 % |
Line Current | 66.4 A 240 V to 80.4 A 200 V |
Apparent Power | 33.5 kVA 240 V |
Transient Overtorque | 120 % of nominal motor torque +/- 10 % 60 s |
Asynchronous motor control profile | Voltage/Frequency ratio, 2 points Voltage/Frequency ratio, 5 points Flux vector control without sensor, standard Voltage/Frequency ratio - Energy Saving, quadratic U/f Voltage/Frequency ratio, automatic IR compensation (U/f + automatic Uo) |
Type of cable | IEC cable without mounting kit 1 45 °C copper 90 °C XLPE/EPR IEC cable without mounting kit 1 45 °C copper 70 °C PVC UL 508 cable with UL Type 1 kit 3 40 °C copper 75 °C PVC |
Electrical connection | Terminal 2.5 mm² AWG 14 VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES Terminal 50 mm² AWG 1/0 L1/R, L2/S, L3/T |
Tightening torque | 24 N.m 212 lb.in L1/R, L2/S, L3/T 0.6 N.m VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES |
Supply | Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <= 10 A overload and short-circuit protection Internal supply 24 V DC 21...27 V <= 200 A overload and short-circuit protection |
Analogue input type | Switch-configurable voltage VIA 0...10 V DC 24 V max 30000 Ohm 10 bits Configurable voltage VIB 0...10 V DC 24 V max 30000 Ohm 10 bits Configurable PTC probe VIB 0...6 probes 1500 Ohm Switch-configurable current VIA 0...20 mA 250 Ohm 10 bits |
Sampling duration | 2 ms +/- 0.5 ms F discrete, 2 ms +/- 0.5 ms R discrete, 2 ms +/- 0.5 ms RES discrete, 3.5 ms +/- 0.5 ms VIA analog, 22 ms +/- 0.5 ms VIB analog |
Response time | 2 ms +/- 0.5 ms FM analog, 7 ms +/- 0.5 ms FLA, FLC discrete, 7 ms +/- 0.5 ms FLB, FLC discrete, 7 ms +/- 0.5 ms RY, RC discrete |
Accuracy | +/- 0.6 % VIA for a temperature variation 60 °C +/- 0.6 % VIB for a temperature variation 60 °C +/- 1 % FM for a temperature variation 60 °C |
Linearity error | +/- 0.15 % of maximum value input VIA +/- 0.15 % of maximum value input VIB +/- 0.2 % output FM |
Discrete output type | Configurable relay logic FLA, FLC NO 100000 cycles Configurable relay logic FLB, FLC NC 100000 cycles Configurable relay logic RY, RC NO 100000 cycles |
Maximum switching current | 5 A 250 V AC resistive cos phi = 1 L/R = 0 ms FL, R 5 A 30 V DC resistive cos phi = 1 L/R = 0 ms FL, R 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms FL, R 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms FL, R |
Discrete input type | Programmable F 24 V DC level 1 PLC 4700 Ohm Programmable R 24 V DC level 1 PLC 4700 Ohm Programmable RES 24 V DC level 1 PLC 4700 Ohm |
Discrete input logic | Positive logic (source) F, R, RES <= 5 V >= 11 V Negative logic (sink) F, R, RES >= 16 V <= 10 V |
Additional Information:
Product Details:
Assembly Style | With Heat Sink |
Phase | 3 Phases |
Maximum Transient Current | 109 Afor 2 s 3 phases 15 kW / 20 hp, 99 Afor 60 s 3 phases 15 kW / 20 hp |
Minimum Switching Current | Configurable relay logic 3 mAat 24 V DC |
Product Or Component Type | Variable Speed Drive |
Connector Type | 1 RJ45 Modbus on front face 1, RJ45 Modbus on terminal Male, SUB-D 9 on RJ45 CANopen |
Transmission Frame | RTU Modbus |
Regulation Loop | Adjustable PI Regulator |
Braking Torque | Less Than or Equal 150 % with braking or hoist resistor 30 % without braking resistor |
Analogue Output Number | 1 |
Component Name | ATV71 |
Discrete Input Number | 7 |
Discrete Output Number | 2 |
Emc Filter | Without EMC Filter |
Frequency Resolution | Analog input 0.024/50 Hz, Display unit 0.1 Hz |
Marking | CE |
Network Frequency | 47.5 to 63 Hz |
Noise Level | 60.2 dB conforming to 86/188/EEC |
Nominal Switching Frequency | 4 kHz |
Operating Position | Vertical +/- 10 degree |
Output Frequency | 0.1 to 599 Hz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Physical Interface | 2-wire RS 485 Modbus |
Pollution Degree | 2 conforming to EN/IEC 61800-5-1 |
Product Destination | Asynchronous Motors, Synchronous Motors |
Product Specific Application | Complex, high-power machines |
Prospective Line Isc | Less Than or Equal 22 kA, 3 phases |
Range Of Product | Altivar 71 |
Supply Voltage Limits | 170 to 264 V |
Switching Frequency | 1 to 16 kHz adjustable, 4 to 16 kHz with derating factor |
Torque Accuracy | +/- 15 % in open-loop mode, without speed feedback +/- 5 % in closed-loop mode with encoder feedback |
Type Of Polarization | No impedance Modbus |
Motor Power kW | 15 kWat 200 to 240 V 3 phases |
Height | 15.75 in (400 mm) |
Depth | 8.39 in (213 mm) |
Width | 48.5 lb(US) (22 kg) |
Dielectric Strength | 2830 V DC between earth and power terminals, 4230 V DC between control and power terminals |
Standards | IEC 60721-3-3 class 3C1, IEC 60721-3-3 class 3S2, UL Type 1 |
Rated Supply Voltage | 200 to 240 V (- 15 to 10 %) |
Shock Resistance | 15 gn 11 ms conforming to EN/IEC 60068-2-27 |
Ambient Air Temperature for Operation | 14 to 122 Deg F (-10 to 50 Deg C) without derating |
Ambient Air Temperature for Storage | -13 to 158 Deg F (-25 to 70 Deg C) |
Model No | ATV71HD15M3X |
Insulation | Electrical between power and control |
Line Current | 61.6 Afor 240 V 3 phases 15 kW / 20 hp, 71.7 Afor 200 V 3 phases 15 kW / 20 hp |
Apparent Power | 25.6 kVAat 240 V 3 phases 15 kW / 20 hp |
Nominal Output Current | 66 Aat 4 kHz 230 V 3 phases 15 kW / 20 hp |
Supply Frequency | 50 to 60 Hz (- 5 to 5 %) |
Synchronous Motor Control Profile | Vector control without speed feedback |
Local Signalling | 1 LED red presence of drive voltage |
Analogue Input Nnumber | 2 |
Braking to Standstill | By DC injection |
Insulation Resistance | Greater Than 1 mOhm at 500 V DC for 1 minute to earth |
Communication Port Protocol | CANopen, Modbus |
Number of Addresses | 1 to 247 Modbus 1 to 127 CANopen |
Motor Power | 20 hpat 200 to 240 V 3 phases |
Method of Access | Slave CANopen |
Motor cable length | <= 164.04 ft (50 m) Shielded cable <= 328.08 ft (100 m) Unshielded cable |
Asynchronous motor control profile | ENA (Energy adaptation) system for unbalanced loads Flux vector control (FVC) with sensor (current vector) Sensorless flux vector control (SFVC) (voltage or current vector) Voltage/Frequency ratio (2 or 5 points) |
Speed range | 1 to 100 asynchronous motor in open-loop mode, without speed feedback 1 to 50 synchronous motor in open-loop mode, without speed feedback 1 to 1000 asynchronous motor in closed-loop mode with encoder feedback |
Speed accuracy | +/- 0.01 % of nominal speed 0.2 Tn to Tn torque variation in closed-loop mode with encoder feedback +/- 10 % of nominal slip 0.2 Tn to Tn torque variation without speed feedback |
Transient overtorque | 220 % of nominal motor torque +/- 10 %for 2 s 170 % of nominal motor torque +/- 10 %for 60 s every 10 minutes |
Motor Slip Compensation | Adjustable Automatic whatever the load Not available in voltage/frequency ratio (2 or 5 points) Suppressable |
Type of cable | With a NEMA Type1 kit: 3-strand UL 508 cableat 104 °F (40 °C), copper 75 °C PVC With an IP21 or an IP31 kit: 3-strand IEC cableat 104 °F (40 °C), copper 70 °C PVC Without mounting kit: 1-strand IEC cableat 113 °F (45 °C), copper 70 °C PVC Without mounting kit: 1-strand IEC cableat 113 °F (45 °C), copper 90 °C XLPE/EPR |
Electrical connection | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 to LI6, PWR terminal 2.5 mm² / AWG 14 L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 35 mm² / AWG 2 |
Tightening torque | AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1 to LI6, PWR 5.31 lbf.in (0.6 N.m) L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 47.79 lbf.in (5.4 N.m) / 47.7 lb.in |
Supply | Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %, <= 10 mAfor overload and short-circuit protection Internal supply, 24 V DC, voltage limits 21 to 27 V, <= 200 mAfor overload and short-circuit protection |
Analogue input type | AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + sign AI2 software-configurable current 0 to 20 mA, impedance 242 Ohm, resolution 11 bits AI2 software-configurable voltage 0 to 10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits |
Sampling duration | AI1-/Al1+ 2 ms, +/- 0.5 ms analog input(s) Al2 2 ms, +/- 0.5 ms analog input(s) LI1 to LI5 2 ms, +/- 0.5 ms discrete input(s) LI6 (if configured as logic input) 2 ms, +/- 0.5 ms discrete input(s) |
Additional Information:
Product Details:
Brand | Schneider |
Assembly Style | With Heat Sink |
Phase | 3 Phase |
Maximum Transient Current | 41.6 A 60 s 11 kW 15 hp |
Minimum Switching Current | 5 mA 24 V DC configurable relay logic |
Product Or Component Type | Variable Speed Drive |
Connector Type | 1 RJ45 Modbus/CANopen on front face |
Regulation Loop | Adjustable PID Regulator |
Transmission Frame | RTU Modbus |
Braking Torque | Less Than or Equal 170 % with braking resistor |
Speed Accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn |
Speed Range | 1 to 100 asynchronous motor in open-loop mode |
Analogue Input Number | 3 |
Analogue Output Number | 1 |
Component Name | ATV32 |
Discrete Input Number | 7 |
Discrete Output Number | 3 |
Emc Filter | Class C2 EMC filter integrated |
Functionality | Mid |
Marking | CE |
Network Frequency | 47.5 to 63 Hz |
Noise Level | 43 dB 86/188/EEC |
Nominal Switching Frequency | 4 kHz |
Operating Position | Vertical +/- 10 Degree |
Output Frequency | 0.0005 to 0.599 kHz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Physical Interface | 2-wire RS 485 Modbus |
Pollution Degree | 2 EN/IEC 61800-5-1 |
Product Destination | Asynchronous Motors, Synchronous Motors |
Product Specific Application | Complex Machines |
Prospective Line Isc | Less Than or Equal 22 kA 3 phases |
Range Of Product | Altivar 32 |
Response Time | 8 ms +/- 0.7 ms LI1 to LI6 logic / 2 ms R1A, R1B, R1C relay / 2 ms R2A, R2C relay |
Supply Voltage Limits | 323 to 550 V |
Switching Frequency | 2 to 16 kHz adjustable |
Torque Accuracy | +/- 15 % |
Model No | ATV32HD11N4 |
Synchronous Motor Control Profile | Vector control without sensor |
Insulation | Electrical between power and control |
Sampling Duration | 2 ms AI1, AI2, AI3 analog, 2 ms AO1 analog |
Linearity Error | +/- 0.2 to 0.5 % of maximum value AI1, AI2, AI3, +/- 0.3 % AO1 |
Braking to Standstill | By DC injection |
Communication Port Protocol | CANopen, Modbus |
Type of Polarization | No Impedance Modbus |
Rated Supply Voltage | 380 to 500 V - 15 to 10 % |
Number of Addresses | 1 to 247 Modbus, 1 to 127 CANopen |
Method of Access | Slave CANopen |
Width | 7.09 in (180 mm) |
Height | 15.91 in (404 mm) |
Product Weight | 19.18 lb(US) (8.7 kg) |
IP Degree of Protection | IP20 EN/IEC 61800-5-1 |
Vibration Resistance | 1 gn 13 to 200 Hz EN/IEC 60068-2-6, 1.5 mm peak to peak 3 to 13 Hz EN/IEC 60068-2-6 |
Supply Frequency | 50 to 60 Hz - 5 to 5 % |
Shock Resistance | 15 gn 11 ms EN/IEC 60068-2-27 |
Relative Humidity | 5 to 95 % without condensation IEC 60068-2-3 5 to 95 % without dripping water IEC 60068-2-3 |
Ambient air Temperature For Storage | -13 to 158 Deg F (-25 to 70 Deg C) |
Motor Power kW | 11 kW 380 to 480 V |
Motor Power | 15 hp 380 to 480 V |
Line Current | 25.6 A 500 V 3 phases 11 kW 15 hp, 36.6 A 380 V 3 phases 11 kW 15 hp |
Apparent Power | 31.7 kVA 500 V 3 phases 15 kW 20 hp |
Nominal Output Current | 27.7 A 4 kHz 500 V 11 kW 15 hp |
Transient Overtorque | 170 to 200 % |
We offer Schneider Altivar 32 Drives VFD to our clients.
Technical Specifications:
Asynchronous motor control profile | Voltage/Frequency ratio, 2 points Flux vector control without sensor, standard Voltage/Frequency ratio, 5 points Voltage/Frequency ratio - Energy Saving, quadratic U/f Flux vector control without sensor - Energy Saving, NoLoad law |
Motor slip compensation | Automatic whatever the load Not available in voltage/frequency ratio (2 or 5 points) Adjustable 0 to 300 % |
Local signalling | 1 LED green CANopen run 1 LED red CANopen error 1 LED red drive fault 1 LED red drive voltage |
Electrical connection | Screw terminal 0.5...1.5 mm² AWG 18...AWG 14 control Removable screw terminals 6...16 mm² AWG 8...AWG 6 motor/braking resistor Screw terminal 10...16 mm² AWG 8...AWG 6 power supply |
Tightening torque | 4.42 lbf.in (0.5 N.m) 4.4 lb/ft control 10.62 lbf.in (1.2 N.m) 10.6 lb/ft motor/braking resistor 10.62 lbf.in (1.2 N.m) 10.6 lb/ft power supply |
Supply | Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <= 10 mA overload and short-circuit protection |
Analogue input type | Voltage AI1 0...10 V DC 30000 Ohm 10 bits Bipolar differential voltage AI2 +/- 10 V DC 30000 Ohm 10 bits Current AI3 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration) 250 Ohm 10 Bits |
Accuracy | +/- 0.2 % AI1, AI2, AI3 for a temperature of -10...60 °C +/- 0.5 % AI1, AI2, AI3 for a temperature of 25 °C +/- 1 % AO1 for a temperature of 25 °C +/- 2 % AO1 for a temperature of -10...60 °C |
Analogue output type | Software-configurable current AO1 0...20 mA 800 Ohm 10 bits Software-configurable voltage AO1 0...10 V 470 Ohm 10 bits |
Discrete output type | Configurable relay logic R1A, R1B, R1C NO/NC 100000 cycles Configurable relay logic R2A, R2B NO 100000 cycles Logic LO |
Maximum switching current | 3 A 250 V AC resistive (cos phi = 1 R1 4 A 30 V DC resistive (cos phi = 1 R1 2 A 250 V AC inductive (cos phi = 0.4 R1, R2 2 A 30 V DC inductive (cos phi = 0.4 R1, R2 5 A 250 V AC resistive (cos phi = 1 R2 5 A 30 V DC resistive (cos phi = 1 R2 |
Discrete input type | Programmable (sink/source) LI1...LI4 24...30 V DC level 1 PLC Programmable as pulse input 20 kpps LI5 24...30 V DC level 1 PLC Switch-configurable PTC probe LI6 24...30 V DC Safe torque off STO 24...30 V DC 1500 Ohm |
Discrete input logic | Negative logic (sink) LI1...LI6 > 19 V < 13 V Positive logic (source) LI1...LI6 < 5 V > 11 V |
Additional Information:
Product Details:
Transmission Frame | RTU |
Dielectric Strength | 2410 V DC between earth and power terminals / 3400 V AC between control and power terminals |
Brand | Schneider |
Motor Power | 2 HP |
Output Frequency | 0 to 500 kHz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Rated Supply Voltage | 380 to 500 V (- 15 to 10 %) |
Supply Voltage Limits | 323 to 550 V |
Supply Frequency | 50 to 60 Hz (- 5 to 5 %) |
Insulation Resistance | Greater Than or Equal 500 mOhm at 500 V DC for 1 minute |
Model No | ATV312HU15N4 |
Network Number of Phase | 3 phase |
Line Current | 6.4 A for 380 V, 5 kA / 4.8 A for 500 V |
Transient Overtorque | 170 to 200 % of nominal motor torque |
Apparent Power | 4.2 kVA |
Power Dissipation | 61 W at nominal load |
Asynchronous Motor Control Profile | Factory set constant torque, Sensorless flux vector control with PWM type motor control signal |
Communication Port Protocol | CANopen Modbus |
Motor Slip Compensation | Adjustable, Automatic whatever the load, Suppressable |
Insulation | Electrical between power and control |
Sampling Duration | AI1, AI2, AI3 8 ms for analog / LI1 to LI6 4 ms for discrete |
Number of Drive | 127 CANopen, 31 Modbus |
Linearity Error | +/- 0.2 % for output |
Discrete Input Type | (LI1 to LI6) programmable, 24 V 0 to 100 mA with PLC, impedance 3500 Ohm |
Local Signalling | 1 LED red for drive voltage, Four 7-segment display units for CANopen bus status |
Time Constant | 5 ms for reference change |
Outer Dimension | 143 x 105 x 150, 184 x 149 x 157, 382 x 239 x 170 mm |
Motor Power kW | 1.5 |
Depth | 152 mm |
Product Weight | 1.8 Kg |
Protective Treatment | TC |
Shock Resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Operating Altitude | Less Than or Equal 1000 m without derating / 1000 to 3000 m with current derating 1 % per 100 m |
Electrical connection | L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 5 mm² AWG 10 Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14 |
Supply | Internal supply for logic inputs at 19...30 V, <= 100 mA for overload and short-circuit protection Internal supply for reference potentiometer (2.2 to 10 kOhm) at 10...10.8 V, <= 10 mA for overload and short-circuit protection |
IP degree of protection | IP20 on upper part without cover plate IP21 on connection terminals IP31 on upper part IP41 on upper part |
Option card | CANopen daisy chain communication card DeviceNet communication card Fipio communication card Modbus TCP communication card Profibus DP communication card |
Braking torque | 100 % with braking resistor continuously 150 % without braking resistor 150 % with braking resistor for 60 s |
Tightening torque | 1.2 N.m L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 0.6 N.m Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1 to LI6 |
Analogue input type | AI1 configurable voltage 0 to 10 V, input voltage 30 V max, impedance 30000 Ohm AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm AI3 configurable current 0 to 20 mA, impedance 250 Ohm |
Analogue output type | AOC configurable current 0 to 20 mA, impedance 800 Ohm, resolution 8 bits AOV configurable voltage 0 to 10 V, impedance 470 Ohm, resolution 8 bits |
Discrete input logic | (LI1 to LI4) logic input not wired, < 13 V (state 1) (LI1 to LI6) negative logic (source), > 19 V (state 0) (LI1 to LI6) positive logic (source), < 5 V (state 0), > 11 V (state 1) |
Discrete output type | (R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles (R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles |
Maximum switching current | R1-R2 on inductive load, 2 A at 250 V AC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on inductive load, 2 A at 30 V DC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on resistive load, 5 A at 250 V AC, (cos phi = 1, and L/R = 0 ms) R1-R2 on resistive load, 5 A at 30 V DC, (cos phi = 1, and L/R = 0 ms) |
Protection type | Input phase breaks drive Line supply overvoltage and undervoltage safety circuits drive Line supply phase loss safety function, for three phases supply drive Motor phase breaks drive Overcurrent between output phases and earth (on power up only) drive Overheating protection drive Short-circuit between motor phases drive Thermal protection motor |
Transmission rate | 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen 4800, 9600 or 19200 bps Modbus |
Additional Information:
Product Details:
Model No | ATV312HU22M2 |
Height | 7.24 in (184 mm) |
Depth | 5.98 in (152 mm) |
Motor Power kW | 2.2 |
Width | 5.59 in (142 mm) |
Standards | IEC 61800-3, IEC 61800-5-1 |
Shock Resistance | 15 gn 11 ms conforming to EN/IEC 60068-2-27 |
Line Current | 18.4 Afor 240 V / 21.9 Afor 200 V, 1 kA |
Apparent Power | 4.4 kVA |
Power Dissipation | 123 W at nominal load |
Asynchronous Motor Control Profile | Factory set constant torque Sensorless flux vector control with PWM type motor control signal |
Insulation | Electrical between power and control |
Communication Port Protocol | CANopen, Modbus |
Transient Overtorque | 170 to 200 % of nominal motor torque |
Motor Slip Compensation | Adjustable, Automatic whatever the loadn, Suppressable |
Sampling Duration | AI1, AI2, AI3 8 ms analog / LI1 to LI6 4 ms discrete |
Linearity Error | +/- 0.2 % output |
Discrete Input Type | (LI1 to LI6) programmable, 24 V 0...100 mA with PLC, impedance 3500 Ohm |
Local Signalling | 1 LED red drive voltage, Four 7-segment display units CANopen bus status |
Time Constant | 5 ms for reference change |
Number of Drive | 127 CANopen / 31 Modbus |
Outer Dimension | 184 x 140 x 150, 215 x 185 x 158, 230 x 200 x 152 mm |
Electrical connection | L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.01 in² (5 mm²) AWG 10 Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1 to LI6 terminal 0 in² (2.5 mm²) AWG 14 |
Supply | Internal supply for logic inputsat 19 to 30 V, <= 100 mAfor overload and short-circuit protection Internal supply for reference potentiometer (2.2 to 10 kOhm)at 10 to 10.8 V, <= 10 mAfor overload and short-circuit protection |
IP degree of protection | IP20 on upper part without cover plate IP21 on connection terminals IP31 on upper part IP41 on upper part |
Option card | CANopen daisy chain communication card DeviceNet communication card Fipio communication card Modbus TCP communication card Profibus DP communication card |
Braking torque | 100 % with braking resistor continuously 150 % without braking resistor 150 % with braking resistor for 60 s |
Tightening torque | 10.62 lbf.in (1.2 N.m) L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 5.31 lbf.in (0.6 N.m) Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1 to LI6 |
Analogue input type | AI1 configurable voltage 0 to 10 V, input voltage 30 V max, impedance 30000 Ohm AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm AI3 configurable current 0 to 20 mA, impedance 250 Ohm |
Analogue output type | AOC configurable current 0...20 mA, impedance 800 Ohm, resolution 8 bits AOV configurable voltage 0...10 V, impedance 470 Ohm, resolution 8 bits |
Discrete input logic | (LI1 to LI4) logic input not wired, < 13 V (state 1) (LI1 to LI6) negative logic (source), > 19 V (state 0) (LI1 to LI6) positive logic (source), < 5 V (state 0), > 11 V (state 1) |
Discrete output type | (R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles (R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles |
Maximum switching current | R1-R2 on inductive load, 2 A at 250 V AC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on inductive load, 2 A at 30 V DC, (cos phi = 0.4, and L/R = 7 ms) R1-R2 on resistive load, 5 A at 250 V AC, (cos phi = 1, and L/R = 0 ms) R1-R2 on resistive load, 5 A at 30 V DC, (cos phi = 1, and L/R = 0 ms) |
Protection type | Input phase breaks drive Line supply overvoltage and undervoltage safety circuits drive Line supply phase loss safety function, for three phases supply drive Motor phase breaks drive Overcurrent between output phases and earth (on power up only) drive Overheating protection drive Short-circuit between motor phases drive Thermal protection motor |
Additional Information:
Product Details:
Brand | Schneider |
Assembly Style | With Heat Sink |
Maximum Transient Current | 6.2 A for 60 s |
Minimum Switching Current | R1-R2 10 mA at 5 V DC |
Product Or Component Type | Variable Speed Drive |
Regulation Loop | Frequency PI regulator |
Speed Range | 1.50 |
Analogue Input Number | 3 |
Height | 143 mm |
Analogue Output Number | 1 |
Width | 107 mm |
Component Name | ATV312 |
Discrete Input Number | 6 |
Discrete Output Number | 2 |
Emc Filter | Integrated |
Marking | CE |
Network Frequency | 47.5 to 63 Hz |
Nominal Switching Frequency | 4 kHz |
Number Of Addresses | 1 to 247 Modbus, 1 to 127 CAN open |
Operating Position | Vertical +/- 10 degree |
Output Frequency | 0.500 kHz |
Output Voltage | Less Than or Equal Power Supply Voltage |
Pollution Degree | 2 |
Product Destination | Asynchronous Motors |
Product Specific Application | Simple Machine |
Prospective Line Isc | 5 kA |
Range Of Product | Altivar 312 |
Response Time | AOV, AOC 8 ms for analog, R1A, R1B, R1C, R2A, R2B 8 ms for discrete |
Supply Voltage Limits | 323 to 550 V |
Switching Frequency | 2.16 kHz Adjustable |
Motor Power | 1.5 kW |
Communication Port Protocol | CANopen Modbus |
Continuous Output Curren | 4.1 A at 4 kHz |
Transient Overtorque | 170 to 200 % of nominal motor torque |
Motor Power HP | 2 |
Motor Slip Compensation | Adjustable, Automatic whatever the load, Suppressable |
Insulation | Electrical Between Power and Control |
Sampling Duration | AI1, AI2, AI3 8 ms for analog, LI1.LI6 4 ms for discrete |
Linearity Error | +/- 0.2 % for Output |
Rated Supply Voltage | 380 to 500 V (- 15.10 %) |
Discrete Input Type | (LI1 to LI6) programmable, 24 V 0 to 100 mA with PLC, impedance 3500 Ohm |
Acceleration and Deceleration Ramps | Linear adjustable separately from 0.1 to 999.9 s S, U |
Braking to Standstill | By DC injection |
Insulation Resistance | Less Than or Equal 500 mOhm at 500 V DC for 1 minute |
Local Signalling | 1 LED red for drive voltage, Four 7-segment display units for CANopen bus status |
Number of Drive | 127 CANopen, 31 Modbus |
Outer Dimension | 143 x 105 x 150, 184 x 149 x 157, 382 x 239 x 170 mm |
Product Weight | 1.8 kg |
Depth | 152 mm |
Supply Frequency | 50.60 Hz (- 5.5 %) |
Dielectric Strength | 2410 V DC between earth and power terminals, 3400 V AC between control and power terminals |
Standards | IEC 61800-3, IEC 61800-5-1 |
Protective Treatment | TC |
Shock Resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
Ambient Air Temperature for Storage | -25.70 Deg C |
Operating Altitude | Less Than or Equal 1000 m without derating, 1000 to 3000 m with current derating 1 % per 100 m |
Network Number of Phases | 3 Phases |
Line Current | 6.4 A for 380 V, 5 kA 4.8 A for 500 V |
Apparent Power | 4.2 kVA |
Power Dissipation | 61 W at Nominal Load |
Asynchronous Motor Control Profile | Factory set constant torque Sensorless flux vector control with PWM type motor control signal |
We offer SchneiderAltivar ATV312HU15N4-VFD to our clients.
Technical Specifications:
Additional Information:
Product Details:
Model Name/Number | NA |
Type of VFD | PWM Drives |
Issue | VFD |
We Repair | Yes |
Location | Onsite |
Usage/Application | Industrial |
Product Details:
Model Name/Number | NA |
Type of VFD | PWM Drives |
Issue | VFD |
We Repair | Yes |
Location | Onsite |
Usage/Application | Industrial |